Langsung ke konten utama

Guide to Remove a Head Unit from a Seventh Generation Honda Civic

This is a stereo/head unit removal DIY for the 03-04 Civic (and may apply to other years as well). This tutorial was created using an 04 LX coupe. The following instructions should be useful to you if you want to change your stereo or install an iPod adapter (such as the popular PA11-Hon).



    1
    Stick your hand under the trim ring and pull.
    Image titled Remove a Head Unit from a Seventh Generation Honda Civic Step 2
    2
    Lift the ring.

    3
    Stick your finger in the location shown and pull up hard. It can be very stiff but it does come out. There is a hole there to stick your finger in and make it easier.

    4
    Be persistent.The console piece does come off but it can be difficult sometimes. If it seems stuck in one part, look very closely to where the clip is (the console piece will be cut out a little just above it), stick a very small screwdriver and try to push the clip out.

    5
    Use a phillips head screwdriver to remove the 2 screws located near the cup holders on either side of the console

    6
    Stick your hand under the "horseshoe shaped piece" as shown and pull it out. It is simply held in by clips, 2 on each side. Pull the sides out first and then pull the entire piece out by pulling up and back. Unplug the cigarette lighter and set this piece aside.

    7
    Start taking the head unit out.

    8
    Remove these 2 screws to allow you to take the panel containing your HVAC controls, hazard light and head unit to come out. You can use either a very short phillips head screwdriver or an 8mm socket and ratchet. One screw is in the center and one is towards the right, but they are up underneath the dash and you may have to get under there at a weird angle to see them, but they are very easy to get out using a ratchet.

    9
    Stick your hand behind the metal bar that you just took the screws out of and push it kind of up and forward. The top of this bar is part of the panel containing the head unit and the bottom half is part of the car. Push on the bar so that the head unit pops out. It may be stiff if it hasn't been removed before but it does come out. It may be helpful to pry at the seams with a spackle knife. Using a screwdriver may not be advisable, because it's too easy to break the plastic. Use force with care.

Komentar

Postingan populer dari blog ini

guide to Power a Car Amplifier Using a Computer Power Supply

If you recently switched vehicles and have no room for that big subwoofer in your new car, don't give it or throw it away. Keep it. Use it inside or outside your house by having it powered by a computer power supply.     1     Find the power pin. In the power supply packaging (if bought new) there should be a pinout diagram. Look for the pin that says something along the lines of “Power on”, "PS OK" or other key words that indicates a on signal. It will be on the biggest pigtail.         99% of the time it will be a green wire on new power supplies, but for older power supply “10+ years” the wire could be yellow or purple. If your power supply did not come with a pinout diagram, check the manufacturer website for a pinout diagram.     2     Cut the power wire from the pin and strip the end.     3     Cut the ground wire from the pin and str...

Guide to Install a Tachometer

A tachometer is used to indicate the revolutions per minute (RPM) being performed by a car engine. Most cars with automatic transmissions are not equipped with a tachometer, since a tachometer is mostly used to indicate visually when it's time to shift gears. If your car doesn't have one, it's a good way to keep an eye on your engine speed. See Step 1 for more information. Getting Started     1     Get a tachometer and splicing connectors. You can either buy a tachometer new, which usually run somewhere between $30 and $50, or salvage on old one for relatively cheap and install it into your car.         The only other specialty item you'll need to complete the job is a package of quick-splice connectors, which are usually only a few dollars at the auto part store. The wires are about 16-18 gauge usually, so get connectors of the appropriate size.     2     Adjust the tachometer for the num...

Guide to Get LoJack for a New Car

"LoJack" is the trade name for a wireless radio transponder the size of a deck of cards that can be installed in a motor vehicle, either at the time of purchase or at a later time, to discourage the vehicle from being stolen. When a LoJack-equipped car is reported stolen, the police activate LoJack's inaudible tracking signal, which can penetrate tunnel and garage walls, ship containers, and dense foliage. If you're planning to buy a new car, you may want to consider buying a LoJack system.     1     Know whether LoJack coverage is available in your area. LoJack's radio signal requires special computer equipment to be tracked; not all police departments have the appropriate equipment. A list of counties within states where LoJack coverage is available is given at http://www.lojack.com/Buy-LoJack-Products/Check-Coverage, and is also available by calling 1-800-456-5225 (1-800-4-LoJack).         The telephone list is usual...