Guide to Determine if Your Car Is Front or Rear Wheel Drive

Automobile drive trains come in 3 types: front-wheel drive, rear-wheel drive and 4-wheel or all-wheel drive. Front-wheel drive cars tend to be smaller, easier to steer and offer better traction in snow or mud, while rear-wheel drive cars tend to be larger, accelerate more quickly, stop more easily and offer a smoother ride. To determine if your car is front- or rear-wheel drive, follow the steps below.

    1
    Locate the engine. Most cars have the engine at the front; these cars may be either front- or rear-wheel drive. Cars with the engine at the rear, such as the Volkswagen Beetle, are always rear-wheel drive cars.

    2
    See how the engine is mounted. If the engine is transverse-mounted (that is, mounted sideways), with the belts facing one side of the car, your car is most likely a front-wheel drive car. If the engine is mounted longitudinally (front to back), with the belts facing the front grille, your car is most likely a rear-wheel drive car.

    3
    Look for a differential. The differential is a large, pumpkin-shaped housing that transfers power from the driveshaft to the wheels. If there is such an assembly on the car's rear axle, the car has a rear-wheel drive. On front-wheel drive cars, the differential is integrated with the transmission in a unit at the rear of the engine called a transaxle, and the wheels are connected to the driveshaft by constant velocity (CV) joints.

Komentar

Postingan populer dari blog ini

guide to Power a Car Amplifier Using a Computer Power Supply

If you recently switched vehicles and have no room for that big subwoofer in your new car, don't give it or throw it away. Keep it. Use it inside or outside your house by having it powered by a computer power supply. 1 Find the power pin. In the power supply packaging (if bought new) there should be a pinout diagram. Look for the pin that says something along the lines of “Power on”, "PS OK" or other key words that indicates a on signal. It will be on the biggest pigtail. 99% of the time it will be a green wire on new power supplies, but for older power supply “10+ years” the wire could be yellow or purple. If your power supply did not come with a pinout diagram, check the manufacturer website for a pinout diagram. 2 Cut the power wire from the pin and strip the end. 3 Cut the ground wire from the pin and strip the end. Refer to the pinout diagram to know which color is the ground wire. 99.9% of the time it will be t

Baca selengkapnya

Guide to Get LoJack for a New Car

"LoJack" is the trade name for a wireless radio transponder the size of a deck of cards that can be installed in a motor vehicle, either at the time of purchase or at a later time, to discourage the vehicle from being stolen. When a LoJack-equipped car is reported stolen, the police activate LoJack's inaudible tracking signal, which can penetrate tunnel and garage walls, ship containers, and dense foliage. If you're planning to buy a new car, you may want to consider buying a LoJack system. 1 Know whether LoJack coverage is available in your area. LoJack's radio signal requires special computer equipment to be tracked; not all police departments have the appropriate equipment. A list of counties within states where LoJack coverage is available is given at http://www.lojack.com/Buy-LoJack-Products/Check-Coverage, and is also available by calling 1-800-456-5225 (1-800-4-LoJack). The telephone list is usually more current than the website list.

Baca selengkapnya

Guide to Program a GM Car Remote Using a Key Fob

Is your old car remote broken, lost, or malfunctioning? This article will show you a quick way to replace your old car remote and save you a lot of money in the process. In this method, a key fob is used to program the remote to your car. This process should work for various GM vehicles from 2005-2012, including models such as Aura, Grand Prix Lacrosse, and Malibu. 1 Enter your vehicle. Work will be done on the driver’s side. 2 Locate the OBD2 Port. This port is located underneath the steering wheel. 3 Close the door you entered through. Make sure all the other doors are closed as well before proceeding. 4 Insert car key into the ignition. Turn the key till the odometer lights turn on. Do not start the engine. 5 Insert the key fob into the port. You only have two minutes to complete the following steps; otherwise the session will time out. 6 Wait for a chime or red light. Once you hear or see it, the remote is ready to be programmed

Baca selengkapnya

motorepair

Cari Blog Ini